If I see it default to 20, I can change to 60 and press extrude.Tiertime Cetus 3D printer is a low-end printer to meet the hobby or DIY project requirements I know I need 3 extrude commands to change filament. The amount that is default could be loaded to a text box where we can edit the amount. I found I need to print one solid model before knowing where I want to insert pauses.ģ) Ability to control the amount of filament per extrude/withdraw command in the maintenence panel. The only beep that is helpful is the one when I've entered a pause height and the head has raised.Ģ) Since there is the ability to set pause height, maybe there should be a way to inspect layers and their respective heights to determine where such pauses should be placed before printing. I don't know what it's doing when it starts or stops but I could really do without both of those beep sequences. Not only should there be a volume setting (including mute), but the option should be made available to configure which events are accompanied by a beep. Since there are no categories on these forums, I figure maybe all suggestions should be together? At some point someone will likely try compiling a list.ġ) I'd like to be able to configure/change/mute the beep. I haven't had the issue with overlapping rafts but if that's an issue, obviously it should be addressed. It's zooming in when I think it should be zooming out. For me the only thing that's off is the middle mouse scroll wheel. I've gotten used to where it is now but it's a bit difficult to access.ģ) Regarding the rotation of the models. One less thing to click.Ģ) Materials under settings. I'd like to "second" a few of your items:ġ) Removing most of the dialog messages. I have a special sawed-of version of a hex tool for tight areas, but I guess most people don't have that :) these screws were difficult to reach, you can't tighten them with the supplied tools because there is not enough room, so you don't want your customers to have to do this. Perhaps look into that at QA during assembly. I had to re-tighen the screws on the motor of the extruder, since they were coming lose (I saw the motor moving up and down during retractions). And since you don't see the rafts directly when you place objects, its kind of a trial and error to get objects close, but not too close to eachother on the print bed.įor the rest I found printing with Cetus a very pleasant experience! Keep up the good work!Īlso. If you place objects near to each other, it tries to print rafts over each other (without a warning), which results in ticking sounds in the extruder. There are lots of wifi's in my area and it seems to find sort of a random list of wifi's of neighbours, but mine is never on this list. I still haven't been able to connect to my wifi. Improve the wifi-searching of the printer. Perhaps it would be easier if you could just rotate around it and zoom in and out, with the bed always staying in the 'up' orientation if you know what I mean. If I try to move the view around my objects I usually end up with the print bed upside down and whatnot, it behaves kind of strange, and different from other 3d printing software 3d views. The free-view rotation is kind of hard to orient. It makes more sense to have a seperate button in the settings menu to look at and adjust the list of materials, instead of having a 'customize' option in the list itself Place the list of materials that you can define under settings, and not under maintanance in the list of materials. It's not like I would accidently click on delete, or accidently click on initialize printer (and so what if I did?) please please remove it, or make an option like 'never ask again' for each of these messages Specially for initializing and removing a model from the printbed, these are really annoying and I don't see the use of those. Remove most of the 'are you sure you want to.' message, these do not seem neccesary. I was used to printing on a glass surface so that gave extremely smooth results.Īnyway, here are some small suggestions based on my experience with the cetus 3d software: One minor thing is that the surface fininsh on the bottom of a print with a raft is not that great, but I'm not sure if that is fixable. Overall, I'm very happy with the Cetus software, it works like it should, and produces very good prints.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |